Can you install your own water heater in Ontario? Parts of the job, possibly. Ontario's electrical regulator lets homeowners do electrical work in their own home once they file a notification, and Oshawa's permit guide lists water heater replacement among plumbing work that does not need a building permit. The plumbing side is less clear, because plumbing is a compulsory trade and the trades law has no written exemption for homeowners. Several rulebooks apply at once: your municipality for the plumbing, the Electrical Safety Authority (ESA) for the wiring, and your rental contract if the tank isn't yours. Gas heaters are another matter.
Can you install your own water heater in Ontario? The short answer
- Is it electric or gas? An electric tank can be a homeowner job if you follow ESA's rules. A gas or propane heater can't (see the TSSA section below).
- Do you own it? Check for a rental agreement before you buy anything. A rented tank belongs to the rental company.
- Is it a straight swap? Same spot, same size, same connections is the easy case. Moving the tank, re-piping it or changing the circuit makes it a bigger job, and in Oshawa it can mean a building permit.
Do you need a building permit to replace a water heater?
The 2024 Building Code (O. Reg. 163/24) came into force on January 1, 2025, and revoked the old code, O. Reg. 332/12. Permits come from your municipality, and each one words its guidance differently.
The City of Oshawa's guide, When do I need a building permit?, lists "repair or replacement of fixture (valve, faucet, fixture, water heater, etc.)" among plumbing work that does not need a permit. The same guide says a "new system, including repair or replacement" does, and the City's building permits page requires one for "making changes to heating or plumbing systems including backflow devices." So in Oshawa, swapping a tank in place is usually permit free; moving it or changing the piping may not be. The guide calls itself "comprehensive, but not exhaustive," and the City takes questions at 905-436-3311.
Whitby's building permits page lists "Plumbing, drains and heating systems" among typical projects that need a permit and doesn't mention water heaters by name, so email building@whitby.ca before you start. Elsewhere in Durham Region, call your building department.
No permit doesn't mean no rules: Part 7 of the code still governs the relief valve and its discharge pipe.
Who is allowed to do plumbing work in Ontario?
Plumber is one of Ontario's 23 compulsory trades, and its scope of practice includes "Connecting any appliance that uses water supplied to it or disposes of waste to piping." Section 6 of the Building Opportunities in the Skilled Trades Act, 2021 reads: "No individual shall engage in the practice of a compulsory trade unless" the person is a registered apprentice, holds a certificate of qualification (or a provisional one), or is exempted by regulation. The exemptions in the Act's general regulation don't mention homeowners, and we found nothing in the Act about someone working on their own house. If you plan to do the plumbing yourself, ask Skilled Trades Ontario how the rule applies to you first.
Hiring is a different story. Section 7 says "No person shall employ or otherwise engage an individual to perform work or to engage in the practice of a compulsory trade" unless they meet the same test. A handyman can't be hired for your plumbing unless they hold a certificate, are a registered apprentice or are exempt. Look anyone up on the Skilled Trades Ontario Public Register.
The electrical side: what ESA requires
An electric tank is hard-wired, and ESA says the Ontario Electrical Safety Code covers "every installation, repair and replacement work." Homeowners may do electrical work in their own home, but ESA's do-it-yourself page sets conditions:
- "Even for little jobs, you must file a notification of work (i.e., permit) with ESA before commencing work."
- "Friends, family members or neighbours cannot perform electrical work in your home."
- "You must get your work reviewed by ESA as soon as it is complete."
Work that passes gets a Certificate of Acceptance, which ESA calls "an important document for insurance purposes and resale." Its notifications page adds that if you hire someone for electrical work in your home, "by law, it must be a Licensed Electrical Contractor," and warns: "Having a building permit isn't the same as filing an electrical notification. You may need both."
Gas water heaters are not a DIY job
TSSA, the Technical Standards and Safety Authority, is blunt in a 2024 safety notice: "In Ontario, furnaces and fuel-fired appliances must be installed and serviced by TSSA-registered contractors who employ certified and trained gas technicians." A natural gas or propane water heater is a fuel-fired appliance. TSSA's contractor lookup lets you check registration.
Hayes installs electric tank water heaters only. We don't install or service gas, tankless or power-vent heaters, and we do no gas line work. For a gas heater, call a TSSA-registered contractor.
Rented tank? Read the contract first
If a water heater charge shows up on a monthly bill, you probably don't own the tank. Ontario's consumer protection guidance points to what to settle before you replace it.
- Find the contract. Two of the province's questions to ask: "When and how can you get out of the contract?" and "What are the consequences and costs if you cancel the contract?"
- Ask about fees. Switching means ending the old contract, and Ontario warns: "There may be fees for ending your current contract and having your existing product or service removed."
- Call your current supplier: "You may be eligible for an upgrade from your current supplier."
- Bought the house recently? You "may be taking on the responsibility for an existing appliance contract that comes with the home."
Be careful at the door. The rules for in-home sales changed on March 1, 2018, and water heaters are on the list of products a business can't sell at your home unless you invited it there to buy or lease one. If a company comes for a repair, "the business cannot enter into a new contract with you." Ontario also says: "do not rely on a salesperson's opinion that your water heater is unsafe or should be replaced." Questions go to Consumer Protection Ontario at 1-800-889-9768.
Safety steps for an electric tank
These follow the GSW manual for its Canadian electric heaters and Part 7 of the 2024 Building Code. Your own heater's manual comes first, and if you are doing the wiring, file the ESA notification before you start, as ESA requires.
- Turn off the power. GSW says to disconnect it "by opening the circuit breaker or removing the fuses," then confirm with a non-contact circuit tester.
- Close the cold supply and drain the old tank. Let the water cool first: GSW warns that "even at 120°F (49°C), hot water can scald." If the shut-off won't close, stop and call.
- Fit the new temperature and pressure (T&P) relief valve that came with the heater. GSW: "Do not reuse an old T&P Relief Valve."
- Run the discharge pipe to code. Article 7.6.1.7 says it must be at least the size of the valve outlet, rigid and sloped downward, ending above a floor drain, sump or other safe location with an air break of not more than 300 mm. No thread at the outlet, rated for at least 99°C, and no shut-off valve on it or between the tank and relief valve. GSW adds: copper or CPVC only, never into the drain pan.
- Plan for thermal expansion. Article 7.6.1.11 requires protection where thermal expansion can occur at check valves, backflow preventers and pressure-reducing valves. GSW says backflow preventers "are often installed in water meters and may not be readily visible," so "almost all homes now need a Thermal Expansion Tank," sized to the heater and pressurized to match your water pressure. Our expansion tank guide explains when you need one.
- Set the new tank in place and connect the cold inlet and hot outlet as its manual shows.
- Fill the tank before any power goes on. Run a hot tap at full stream for three full minutes. GSW's warning: "If power is applied before the tank is completely full of water, the upper element will burn out (Dry Fire)." It calls that "an installation error" that "is not covered under warranty."
- Wire it to match the data plate (GSW says to confirm the voltage, wire size and breaker suit the heater), restore power, and book your ESA review.
- Dry the pipes so any drip shows, then check every connection.
An old tank you owned can go out with metal goods: the Region of Durham's metal goods list includes "Hot water tanks (drained)," picked up by appointment. Oshawa residents book through the City (905-436-3311) and Whitby residents through the Town (905-668-3437). A rented tank goes back to the rental company.
Set the temperature with scalds and Legionella in mind
The Public Health Agency of Canada's water temperature page gives two numbers. Set the water heater to 60°C (140°F) "to prevent the growth of harmful bacteria such as Legionella." Then guard against scalds with mixing valves on faucets, showers and tubs, or an anti-scald valve on the heater, set to 49°C (120°F). It also notes: "A child's skin burns in a quarter of the time it takes an adult's skin to burn."
The Building Code uses the same 49°C cap for water from a shower head or into a bathtub (Article 7.2.10.7). GSW warns that "even at 120°F (49°C), hot water can scald." So if you raise the tank to 60°C, the mixing valve is what keeps the taps safe.
What you can reasonably do, and when to call a registered plumbing technician
| Your situation | DIY or call? | Why |
|---|---|---|
| Same size electric tank, same spot, working shut-off, floor drain close by | The smallest job; check the rules first | ESA notification for the wiring; ask Skilled Trades Ontario about the plumbing |
| The tank is rented | Rental company first | It's their tank, and ending the contract may carry fees |
| Gas or propane heater | TSSA-registered contractor | TSSA requires it; Hayes does no gas work |
| Moving the heater or changing the piping | Call us | Oshawa requires a permit for changes to plumbing systems |
| Bigger tank or a different model | Call us | The circuit and breaker must suit the new data plate |
| Seized shut-off or old galvanized steel connections | Call us | You can't isolate the tank, and the code (Article 7.2.6.7) allows galvanized steel in water lines only to repair existing galvanized piping |
| No floor drain or safe spot for the relief discharge | Call us | The pipe has to end at a drain, sump or other safe location |
| The circuit needs new wiring or a new breaker | Licensed Electrical Contractor, or you with an ESA notification | ESA's rules apply |
| Relief valve keeps dripping | Call us | GSW says "High water pressure can cause the T&P Relief Valve to drip" |
What Hayes does
Hayes Plumbing has been family owned in Oshawa since 1961, and we install electric tank water heaters across Durham Region. A registered plumbing technician removes the old unit and installs the new tank to code with its relief valve and drain, and we pull the permit when the job needs one. Our 2026 cost guide lists electric tank water heater installation at $500 to $1,500, depending on model and installation complexity. In-home estimates are free, and you get a written quote before any work starts.
See our water heater service page, or read hot water tank replacement in Oshawa for signs a tank is near the end. Call (905) 576-3043 (a live operator answers 24/7 for emergencies) or book a visit online.

